Superfil Sandable Non-Shrinking Epoxy Filler Quart Kit

Image for illustration only. It may show a product series rather than the exact product offered.

Superfil Sandable Non-Shrinking Epoxy Filler Quart Kit

Hazardous material Special shipping rules and carrier restrictions may apply.

Part numbers : RX1-09-28250 , 8-EF3 , 09-28250

Unit of Measure: QT

61.83 EUR / QT 61.83 EUR 61.83 € excl. VAT

61.83 EUR / QT excl. VAT

This combination does not exist.

102 QT available on request, fees apply

Hazardous material special order from vendor stock.

Add to cart

Poly-Fiber SuperFil 8-EF3 is a lightweight, two-part epoxy filler kit designed for rough filling and contouring prior to sanding and finishing. Its non-shrinking formulation provides a consistent, sandable filler for maintenance, repair and finishing work.

Manufacturer part number: 8-EF3
Quart kit containing resin and hardener components
Suitable for use on composites, bare aluminium, steel, and bare or varnished wood when surfaces are prepared in accordance with the manufacturer’s instructions
May be applied by squeegee or trowel and sanded after cure
Mix ratio: 2 parts resin to 1 part hardener, by weight or volume
Non-shrinking epoxy filler formulated for lightweight filling and contouring

Stir each component thoroughly before combining, then mix to an even colour before application. Follow the current manufacturer application instructions and safety data documentation, including all surface-preparation, curing and personal-protection requirements.

Documents

Part A MSDS

Part B MSDS

Orders with purchased items below 100.00 € incur a small order fee of 10.00 €. Both amounts exclude VAT. Shipping, other fees and core deposits do not count towards the limit.

Terms and Conditions

Description	Part Number
Poly-Fiber SuperFil 1 Qt Kit (20oz. Resin / 12oz. Hardener)	09-28250

Overview

An ultra lightweight corrosion-inhibiting filler for aircraft, marine, and automotive use. Adheres to composites, bare aluminum, steel, and bare or varnished wood.

Epoxy resin with non-MDA hardener. Ships non-hazardous. Apply EP-420 Epoxy Primer directly over SuperFil.

Superfil is an ultra-lightweight epoxy filler for rough fill and contouring. Comes in two containers. Mix, apply with a squeegee, and let dry overnight. More consistent than hand-mixed micros. Weighs only 3.8 lbs. per gallon.

1 Quart Kit (12 oz. Hardener + 20 oz. Resin)
3 Gallon Kit (1 gal. Hardener + 2 gal. Resin)

HAZARDOUS

Features

Composite Filling:
Use as you would an epoxy micro slurry. Mix by the weight for the best results. Scuff-sand smooth surfaces before application. Trowel or squeegee to desired thickness. After drying, sand to shape and finish. Works as an excellent filled material.
Bare Aluminum:
Scruff surface with a Scotch-Brite pad. Treat bare aluminum with E-2300 Conversion Coating prior to application. Apply EP-420 Primer directly over dried SuperFill.
Bare Steel:
Clean off all rust and oil, and wipe with C-2200 Meti-Sol.
Varnished or Bare Wood:
Scuff-sand and clean as necessary. EV-400 Epoxy Varnish may be applied directly over SuperFill.

Specifications

By Weight (preferred): 2 parts A to 1 part B
By Volume: 2 parts A to 1 part B.
Thoroughly stir each individual container of part A and part B before combining. Resin or hardener can separate from fillers during storage. After combining parts A and B scape the sides of the Revision on 21 mixing container to insure a through blend. Mix o a consistent high color blue color.
Cure: Allow to cure at 70° or above for best results. Lower temperatures will lengthen the cure time
Dry Film Cure: 8 hours at 77°
Cure to Sand: 12 hours at 77°
Pot Life: One hour at 77°
Clean Up: MEK before curing occurs
Shelf Life: Twi years unopened. Avoid storage above 100°. Resin will separate from filler during storage. Remix thoroughly.

These products might also be of interest